Shopping Cart
Your Cart Is Empty
Stainless Steel Category 3 Adjustable Length Vent Pipe
Stainless Steel Category 3 Standard Vent Pipe
Stainless Steel Category 3 Vent 90 Degree Elbow
Stainless Steel Category 3 Vent 30 Degree Elbow
Sterling GG Inlet Air Collar
Stainless Steel Category 3 Vent Tee Condensate Cap
Stainless Steel Category 3 Vent Tee
Stainless Steel Category 3 Vent Drip Tee
Stainless Steel Category 3 Vent 45 Degree Elbow
Sterling GG120 Gas Heater
Sterling GG45 Gas Heater
Sterling GG75 Gas Heater
For Sterling models GG30, GG45, GG60, GG75, GG90, GG105, & GG120Each vent system comes complete with everything needed to vent a Sterling GG heater. These stainless steel, gas tight 4" vent systems are approved by Sterling for horizontal installation in residential and commercial applications for GG model heaters. These are the most durable, longest lasting, and lowest maintenance vent systems available for these gas heaters. All vent systems are for horizontal venting of all Sterling GG gas heaters.
Sterling 4" Greenhouse Vent Kit IncludesFor greenhouses and structures with walls less than 4" thick.(1) 4" heater adapter, (1) 4" vent terminal, (1) 4" x 24" vent pipe, (1) 4" x 35" adjustable vent pipe, (2) 4" Firestop flashings, and (1) 4" storm collar Sterling 4" Garage / Shop Vent Kit IncludesFor structures with an exterior wall at least 4" thick. Adjustable length.(1) 4" heater adapter, (1) 4" vent terminal, (1) 4" x 24" vent pipe, (2) 4" x 12" vent pipes, and (1) 4" adjustable wall thimble + 18" pipe Sterling 4" 45 Degree Garage / Shop Vent Kit IncludesFor heaters installed at a 45 degree angle to the wall in structures with an exterior wall at least 4" thick. Adjustable length.(1) 4" heater adapter, (1) 4" vent terminal, (1) 4" 45° elbow, (2) 4" x 12" vent pipes, and (1) 4" adjustable wall thimble + 18" pipe
Vent pipe and fittings feature patented built-in mechanical locking band and triple-lipped directional gaskets. All pipes and components are engineered with smooth clean welds located 90° from mechanical locking bands. All pipe and fittings are UL1738 approved for category II, III and IV venting applications.
What is UL 1738? In short, it is a US standard for gas venting systems required in category 3 applications. Category 3 refers to positive vent pressure which is created by exhaust blowers in unit heaters. These vent systems must be constructed of AL29-4C® stainless steel, contain gaskets for sealing, and have a built in mechanical locking band among other requirements. All category 3 vent pipe and fittings offered are single wall.
Item # 465110, 4651105, 4651100, 4651102
We took our time and lined up the vent to fit between the ribs on a pole building. All parts fir together perfectly.
Cat 3 vent pipe green house kit went together very well just wish there would have been some instructions. Bought a thimble and used instead of green house plates because of my material in wall.ACF Greenhouses: I'm sorry you did not receive instructions for installing the vent system. They should have been in a red envelope included with your order.
We installed a natural gas heater in our garage. This unit along with the thimble extender was exactly what we needed. We had a wall 11” thick to go thru and no other item would work for us. They shipped quickly and it was perfect for our install.
It was a breeze doing business with ACF greenhouses. Fast shipping and all their products are of best quality. Trust worthy!!!!!
This kit was everything I needed to get my garage heater installed. It's a nice kit I was looking around on a few different sites but I'm glad I ordered this one. Maybe it was just me but horizontal vent kits aren't easy to find and some of the kits were alot more than this one!
Venting kit worked well.
I liked that piping was stainless and had joint seals built into it. The piping was easily installed with one section being adjustable for length. One problem I had was the end cap joint. When tightening the clamp it wouldn’t secure the end cap. If I continued to tighten it it would crush the slip joint. To solve this problem I made a 4” diameter ring from band iron that slipped inside the pipe joint. This gave the clamp something to clamp against without crushing it.
Good luck finding this stuff locally. I checked with 3 hvac equipment suppliers and none of people there even knew what category 3 or ul1738 was. I resorted to searching online for it and luckily found ACF. I asked the salesperson if this was some special venting required only by Sterling. He told me it is the same piping that has been required for all heaters like this since like 2012. WOW! Glad I didn't listen to these other stores who were trying to sell me something not even appropriate for this heater.
Just what I needed. Looks great and went together easily.